FLX ASI DI 4 M12

FLX ASI DI 4 M12 I1 I2 Fieldline Extension AS-i M12 device with four digital inputs I3 I4 PW R FA UL T FL OrdX AS er- I D No I 4 .: 2 M 7 7 12 34 29 co © PHOENIX CONTACT - 01/2009 Description Features ne po om – – in ec – – – on l – – Four digital inputs AS-i connection via flat-ribbon cable (penetration technique) No tools required for connection to the flat-ribbon cable Connection of digital sensors using M12 connectors (SPEEDCON fast connection technology) AS-i voltage indication Diagnostic and status indicators Short-circuit and overload protection of the sensor supply AB slave IP65/IP67 degree of protection nt s. The device is designed for use within an AS-Interface system. It is used to acquire digital signals. – – m Data sheet 7465_en_01 1 AD DR AUTOMATION Make sure you always use the latest documentation. It can be downloaded at www.phoenixcontact.net/download. FLX ASI DI 4 M12 2 Ordering data Type Order No. Pcs./Pkt. Fieldline Extension AS-i M12 device with four digital inputs FLX ASI DI 4 M12 2773429 1 Accessories Description Type Order No. Pcs./Pkt. Protective caps (for unused female connectors) PROT-M12 1680539 5 Manual addressing device for AS-Interface devices ASI CC ADR 2741338 1 Programming cable for connecting AS-Interface devices to the manual addressing device ASI CC ADR CAB CINCH 2741341 1 m Device Description Documentation Description s. co Additional accessories for connecting the sensors can be found in the Phoenix Contact PLUSCON catalog. Pcs./Pkt. UM EN FLX ASI SYS PRO INST – – User Manual: AS-Interface addressing device ASI CC ADR UM E 9013727 1 ne Technical data 58 om 108 in ec 29 46 34.5 155 po 3 Type nt Order No. User Manual: Configuring and installing of devices in the Fieldline Extension AS-Interface product group 118 Dimensions of the device in mm on l Figure 1 7465B002 General data Dimensions (width x height x depth); including mounting base 58 mm x 118 mm x 34.5 mm Weight 195 g Connection method for sensors 2, 3, and 4-wire technology Permissible temperature (operation) -25°C to +70°C Permissible temperature (storage/transport) -25°C to +85°C Degree of protection IP65/IP67 according to IEC 60529 Protection class Class 3 according to IEC 61140 7465_en_01 PHOENIX CONTACT 2 FLX ASI DI 4 M12 Mechanical requirements Vibration test, sinusoidal vibrations according to EN 60068-2-6 5 g load in each space direction Shock test according to EN 60068-2-27 30 g load, half sinusoidal wave positive and negative in each space direction For additional information on mechanical requirements and ambient conditions, please contact Phoenix Contact. Power supply Communications power and sensor supply voltage ULS 26.5 V to 31.6 V from AS-Interface ≤ 40 mA + sensor current (200 mA, maximum) Surge protection ULS: Surge Voltage Category III m Current consumption at ULS Digital inputs 4 Input design According to IEC 61131-2 Type 2 co Number Maximum low-level voltage ULmax < 5 V Minimum high-level voltage UHmin > 11 V 30 V DC from AS-i nt Nominal input voltage s. Definition of switching thresholds -3 V DC < UIN < +30 V DC 8 mA Current flow Non-linear < 10 mA ne Range Nominal input current Delay time tON < 1 ms, typical tOFF < 1 ms, typical < 30 m 0 1 2 in ec 3 om Input characteristic curve Input voltage (V) Typical input current (mA) 0 0.5 1.1 1.7 4 2.3 5 3.0 6 3.6 7 4.3 8 5.1 on l 7465_en_01 po Permissible cable length to the sensor 9 6.1 10 7.0 11 7.9 12 8.0 15 8.0 18 8.1 21 8.1 24 8.2 27 8.2 30 8.3 PHOENIX CONTACT 3 FLX ASI DI 4 M12 Sensor supply Minimum sensor voltage ULS – 7 V Nominal current per channel 200 mA Nominal current per device 200 mA Connections AS-Interface Flat-ribbon cable penetration technique Inputs M12 female connector Electrical isolation/isolation of the voltage ranges Separate potentials in the FLX ASI DI 4 M12 device Test distance m Test voltage 500 V AC, 50 Hz, 1 min. co 30 V supply (sensor supply and communications power and inputs)/ housing Approvals 4.1 AS-i connection nt Pin assignment ne 4 s. For the latest approvals, please visit www.phoenixcontact.net/download or www.phoenixcontact.net/catalog. Designation IN1 to IN4 AS-i Meaning Inputs 1 to 4 Connection to AS-i (bus and power supply) IN3 AS-i on l IN1 in ec om po A connection to the AS-Interface is established by inserting the AS-i flat-ribbon cable in the cable routing aid provided in the mounting base of the device, and then making contact with the module electronics. Contact is established as soon as the locking latch snaps in. IN2 IN4 AS-i 7465B003 Figure 2 7465_en_01 Connections of the FLX ASI DI 4 M12 device PHOENIX CONTACT 4 FLX ASI DI 4 M12 4.2 Pin assignment of the inputs Pin 1 2 3 4 5 6 6 2 5 A 0 0 6 Figure 3 Female input connectors IN2 IN3 IN4 Sensor supply + Not used IN4 Not used Sensor supply IN2 IN3 IN4 Not used IN1 IN2 IN1 Pin assignment of the inputs s. Local diagnostic and status indicators nt 5 co m The M12 connectors are designed for a tightening torque of 0.4 Nm. I3 I4 Figure 4 7465_en_01 in ec on l PWR FLT po I2 om I1 ne Designation I1 to I4 PWR FLT Color Yellow ON OFF Green Flashing green Red Flashing red Meaning Status indicators of the inputs Input active Input not active AS-i supply voltage Address 0 Communication failure Sensor overload 7465B004 Local diagnostic and status indicators of the FLX ASI DI 4 M12 device PHOENIX CONTACT 5 FLX ASI DI 4 M12 6 Internal basic circuit diagram Key: LED Input Overload protection Filter Optocoupler 4 Protocol chip ne nt A S I 4 U s. O v e r lo a d P r o te c tio n co 4 m O v e r lo a d P r o te c tio n om po A S I 4 U Internal wiring of the connections on l Figure 5 in ec 7 4 6 5 A 0 0 5 7465_en_01 PHOENIX CONTACT 6 FLX ASI DI 4 M12 Connection examples IN 2 IN + 1 IN -1 IN 1 IN -2 IN 2 IN 1 IN + 2 7 Typical connection of sensors in 3-wire technology s. co Figure 6 m 7 4 6 5 A 0 0 6 IN 2 ne po IN + 1 IN -1 Typical connection of sensors in 4-wire technology Connection notes in ec 8 7 4 6 5 A 0 0 7 om Figure 7 IN 1 IN 2 nt IN 1 on l NOTE: When using 4-wire sensors, opposite slots must not be used. NOTE: Avoid compensating currents Each individual sensor must be insulated. NOTE: Ensure degree of protection NOTE: To ensure IP65/IP67 protection, cover unused female connectors with protective caps. NOTE: Avoid damage to the electronics Fix the device to a level surface or to a profile. Do not use the device to bridge gaps, in order to prevent forces from being transmitted via the device. An external power supply unit must never be used to supply the sensors. NOTE: Tighten the mounting screws to a maximum of 2.8 Nm. 7465_en_01 PHOENIX CONTACT 7 FLX ASI DI 4 M12 9 Programming data 9.1 Configuration data IO code 0hex ID code Ahex (extended addressing) ID1 code 7hex (can be defined by the user) ID2 code 2hex Profile S-0.A.2. AS-i specification 2.1 (AB slave) Bit D0 IN Input IN1 D0 OUT Not used D1 IN Input IN2 D1 OUT Not used D2 IN Input IN3 D2 OUT Not used D3 IN Input IN4 D3 OUT Not used Function P0 Not used P1 Filter for the inputs in the AS-i IC P1 = 0: Activated P1 = 1: Deactivated P2 Synchronous mode P2 = 0: Activated P2 = 1: Deactivated P3 Not used on l in ec om Bit ne Parameter bit (programmable via AS-Interface) po 9.3 Function co Function s. Bit m Data bit (function via AS-Interface) nt 9.2 7465_en_01 PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany • Phone: +49-(0) 5235-3-00 PHOENIX CONTACT • P.O.Box 4100 • Harrisburg • PA 17111-0100 • USA • Phone: +1 (0) 717-944-1300 www.phoenixcontact.com 8